Best way to repair bent sides?

Talk about musical instrument construction, setup and repair.

Moderators: kiwigeo, Jeremy D

Post Reply
User avatar
Bob_H
Blackwood
Posts: 156
Joined: Sat Apr 11, 2020 2:27 pm
Location: Lyndoch, South Australia

Best way to repair bent sides?

Post by Bob_H » Sat May 02, 2020 2:14 pm

With the neck block fitted and the sound board in place, it is clear that the sides are a couple of mm too deep for the neck. I could taper the sides, reduce the overall depth or build up the neck block. Suggestions or advice received gratefully :)
Attachments
12980F4F-DC89-43A1-AFD7-DD1827903E06.jpeg
12980F4F-DC89-43A1-AFD7-DD1827903E06.jpeg (85.47 KiB) Viewed 11565 times
Bob Holbert
Lyndoch

CNCWorksNZ
Kauri
Posts: 38
Joined: Sat Jun 22, 2019 6:15 pm
Location: Wellington, New Zealand.

Re: Best way to repair bent sides?

Post by CNCWorksNZ » Sat May 02, 2020 8:47 pm

You could put a nice contrasting Heel Cap in that space ... That's what I would do, just for the hell of it ...

User avatar
Lillian
Blackwood
Posts: 1705
Joined: Fri Sep 28, 2007 10:31 pm
Location: New Mexico, USA
Contact:

Re: Best way to repair bent sides?

Post by Lillian » Sat May 02, 2020 10:43 pm

You could do both, put a heel cap on and then taper from the waist to meet it.

User avatar
Allen
Blackwood
Posts: 5252
Joined: Thu Oct 11, 2007 5:39 pm
Location: Cairns, Australia
Contact:

Re: Best way to repair bent sides?

Post by Allen » Sun May 03, 2020 6:40 am

If your sides are the same depth at tall block and neck then your uke is going to look pretty strange. They should taper in body depth from deepest at tail block to the neck. I use 10mm between the two on all sizes of my ukes.

Pretty easy to achieve this by using a small plane and pare away excess from waist to neck and then use a piece of plywood or mdf with 80 grit sandpaper to level / even out the transition.....or a radius dish if you are going with that type of back.

I have a radius dish mounted to an old repurposed potters wheel and this job would take me 30 seconds to a minute.
Allen R. McFarlen
https://www.brguitars.com
Facebook
Cairns, Australia

User avatar
Bob_H
Blackwood
Posts: 156
Joined: Sat Apr 11, 2020 2:27 pm
Location: Lyndoch, South Australia

Re: Best way to repair bent sides?

Post by Bob_H » Sun May 03, 2020 6:52 am

Thanks all. I think a taper and heal cap sound like a plan. I’m not using an arched back and haven’t put together a radius dish at this time, so plane and sand.
Bob Holbert
Lyndoch

johnparchem
Blackwood
Posts: 546
Joined: Mon Jan 21, 2013 2:59 am
Location: Seattle
Contact:

Re: Best way to repair bent sides?

Post by johnparchem » Sun May 03, 2020 11:46 am

This all looks normal to me. Agree with taper the sides, the block and the heel cap until all is in plane.

User avatar
kiwigeo
Admin
Posts: 10582
Joined: Sat Sep 29, 2007 5:57 pm
Location: Adelaide, Sth Australia

Re: Best way to repair bent sides?

Post by kiwigeo » Sun May 03, 2020 5:58 pm

If the sides aren't tapered...then it's a banjo....and we don't wanna be buildin' banjas do we??? :mrgreen:
Martin

CNCWorksNZ
Kauri
Posts: 38
Joined: Sat Jun 22, 2019 6:15 pm
Location: Wellington, New Zealand.

Re: Best way to repair bent sides?

Post by CNCWorksNZ » Sun May 03, 2020 6:48 pm

Can anyone explain why a Ukulele should be tapered?
Is there any Acoustical reasoning behind this, or is it just traditional?

.

User avatar
Lillian
Blackwood
Posts: 1705
Joined: Fri Sep 28, 2007 10:31 pm
Location: New Mexico, USA
Contact:

Re: Best way to repair bent sides?

Post by Lillian » Mon May 04, 2020 3:25 am

kiwigeo wrote:
Sun May 03, 2020 5:58 pm
If the sides aren't tapered...then it's a banjo....and we don't wanna be buildin' banjas do we??? :mrgreen:
You mean like this
https://www.youtube.com/watch?v=wYQsLSNzBhY

johnparchem
Blackwood
Posts: 546
Joined: Mon Jan 21, 2013 2:59 am
Location: Seattle
Contact:

Re: Best way to repair bent sides?

Post by johnparchem » Mon May 04, 2020 4:40 am

CNCWorksNZ wrote:
Sun May 03, 2020 6:48 pm
Can anyone explain why a Ukulele should be tapered?
Is there any Acoustical reasoning behind this, or is it just traditional?

.
They do not need to be and many traditional ukulele's are not. I think the tapered sides on a tenor looks better. It matters less to me with a soprano or true ukulele. I made my suggestion as the heel block was sized assuming a tapered back.

CNCWorksNZ
Kauri
Posts: 38
Joined: Sat Jun 22, 2019 6:15 pm
Location: Wellington, New Zealand.

Re: Best way to repair bent sides?

Post by CNCWorksNZ » Mon May 04, 2020 8:36 am

johnparchem wrote:
Mon May 04, 2020 4:40 am
CNCWorksNZ wrote:
Sun May 03, 2020 6:48 pm
Can anyone explain why a Ukulele should be tapered?
Is there any Acoustical reasoning behind this, or is it just traditional?

.
They do not need to be and many traditional ukulele's are not. I think the tapered sides on a tenor looks better. It matters less to me with a soprano or true ukulele. I made my suggestion as the heel block was sized assuming a tapered back.

Thanks for that. My current challenge is a Baritone Ukulele built entirely from a 1919 John Brinsmead Piano which will be 85mm deep throughout, (no Taper).
I dismantled one over the last few Weeks and can confirm that it's not worth the effort.
I'll get 2 Baritone sized Sound/Back Boards & 1 Classical and a lifetime of Brace Material and that's it. The Piano didn't have the decency to supply ivory Keys :x

Post Reply

Who is online

Users browsing this forum: No registered users and 71 guests