Search found 33 matches

by stevemc32
Sat Sep 12, 2020 9:14 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Thanks Pat, the undersize tang was definitely my problem with the first set of frets, it was not something I'd considered before. I made a fret bender a long time ago that looks very similar to the one you mentioned but I used sliding door rollers. I don't need any sort of drive for this one, just p...
by stevemc32
Thu Sep 10, 2020 7:10 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Nailed it Mark, I had to push it down with a fingernail over the nut to stop the buzzing but it did the job. Managed to re-file it a little and got it sorted out. So it's all done and sounding great. Thanks for the help throughout to all who contributed. Now time to finish reading the books and get ...
by stevemc32
Mon Sep 07, 2020 5:55 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Ok, I've done a quick setup on it and the saddle is a little more respectable in height above the bridge. There's a couple of rattles from the onboard pre-amp wires that I need to sort out but that shouldn't be a major issue. I do have a problem in that the open b string makes a horrible whistling s...
by stevemc32
Thu Sep 03, 2020 10:49 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Thanks for the kind words Gents, still need to work on the frets and get the action set up correctly before I can have a good play but it did sound nice when first strung up. There's a lot of potential guitars up on those wood shelves and I like to think they've just been acclimatising for the last ...
by stevemc32
Tue Sep 01, 2020 9:12 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Stringed it up today and made some noise. 20200901_180447.jpg Started off with a super tall saddle to compensate for my neck angle error but looks like I might be able to take a couple of millimetres off and still get reasonable action. It's not ideal but also not as bad as I was expecting. Below is...
by stevemc32
Mon Aug 31, 2020 5:56 pm
Forum: Instrument Builders Forum
Topic: Saddle position
Replies: 31
Views: 25242

Re: Saddle position

With regards to the bridge height, I normally aim for the straight edge to be just be kissing the top of the bridge. I can't quite tell what sized gap it is but anything more than say a mm is too much. Even a 1mm mil is pushing it. I have a problem with this too and I think it could be something th...
by stevemc32
Sun Aug 23, 2020 9:39 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Got hold of the books and have been reading about all the things I could've done differently on this build... Should be interesting to see how the next one compares. Anyhow, I'm up to the bit where you get to finally see the timber and forget (ignore for just a little while) the things you stuffed u...
by stevemc32
Wed Aug 19, 2020 6:36 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Cut a hole and glued the bridge on. Haven't used any onboard electronics on the previous ones so this is a bit different for me. Had mixed feelings on whether or not to go ahead with it but that was always the plan for this one so I figured I might as well stick to it. 20200819_135253.jpg 20200819_1...
by stevemc32
Tue Aug 18, 2020 6:02 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Got the bridge made up and started sanding. Looks like I might have angled the neck a little too far in the end. A straight edge from the frets to the bridge sits about 2mm above it where I was expecting it to sit just about on top of the bridge. I guess a taller saddle might sort it out but it's no...
by stevemc32
Sat Aug 15, 2020 8:10 pm
Forum: Instrument Builders Forum
Topic: Number 2.- Tenor Uke
Replies: 4
Views: 4773

Re: Number 2.- Tenor Uke

Looks great Bob, love the Tiger Myrtle!
by stevemc32
Sat Aug 15, 2020 8:07 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Cheers Mark. Got some sawdust and CA filling done on the fretboard today and refretted using the wider tang frets. Most of the damage got covered up but there's still one or two chips that I overlooked and will need to catch up with now. The frets feel much better and I think the problem is solved. ...
by stevemc32
Fri Aug 07, 2020 8:16 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Sounds good Trent, definitely a method I'll keep in mind. I did bevel the slots Martin, but today's results have shown me that I haven't done it anywhere near wide enough to be useful. I'll go a little further with the bevelling next time for sure. Along with my fret removing pliers I bought a pair ...
by stevemc32
Fri Aug 07, 2020 5:36 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

It looks pretty horrible! 20200807_144524.jpg The third fret and a couple up on the soundboard are probably the worst of them. Fortunately there's really no long grain in the Lace Sheoak so the chips are mostly limited to a size that should be covered by the new frets. I've sealed them all up and se...
by stevemc32
Thu Aug 06, 2020 10:29 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

That's an interesting fretting method Trent, can't say I've heard of that one before but sounds like it would solve my problem. I think I'll replace them though as I've already got the wire. Did you tint the epoxy, looks black in the syringe? I really like the soundhole inlay on that guitar of yours...
by stevemc32
Wed Aug 05, 2020 5:04 pm
Forum: Instrument Builders Forum
Topic: Nicco's Lying-Around-Timber-o-Caster
Replies: 14
Views: 10635

Re: Nicco's Lying-Around-Timber-o-Caster

Sounds good nicco, thanks for the info!
by stevemc32
Wed Aug 05, 2020 5:00 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Yeah Mark they're all loose. They actually kind of sing when I run my fingernail down the fretboard, each one plays it's own note. I've got a set of fret removing pliers on the way, should be here on Friday so I'll just take it easy till then and see how they go coming out. I did glue them in with j...
by stevemc32
Tue Aug 04, 2020 2:12 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

I think you've nailed it Martin, I just went and measured the tang width on the fretwire I used and it was 0.4mm where the saw (and my usual fretwire) is 0.6mm. I'm guessing they've all got to come out, which is a real pain as the Sheoak suffered some damage when I took the two out I was using for n...
by stevemc32
Mon Aug 03, 2020 8:06 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Fretted up today and might have a bit of a problem. The frets felt sort of loose when I was filing off the ends in that I could feel them vibrating when the file ran over them, I don't remember that from last time. I also noticed that a couple of the ends were not holding down in the slots and might...
by stevemc32
Mon Aug 03, 2020 9:57 am
Forum: Instrument Builders Forum
Topic: Nicco's Lying-Around-Timber-o-Caster
Replies: 14
Views: 10635

Re: Nicco's Lying-Around-Timber-o-Caster

I have a friend who has offered to do some laser cutting for inlays but I was worried that the burn marks on the edges might be visible.

I can't tell from your photo, which is a good thing, but is there any burning or black outline on your dots after they've been placed and sanded flush?
by stevemc32
Sun Aug 02, 2020 9:00 pm
Forum: Instrument Builders Forum
Topic: Nicco's Lying-Around-Timber-o-Caster
Replies: 14
Views: 10635

Re: Nicco's Lying-Around-Timber-o-Caster

Nice work, looks like it did the job well!
by stevemc32
Sun Aug 02, 2020 7:26 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Got the fretboard glued on and the neck shaped up. Still a few areas to work on but it's fairly close to final shape now.
20200802_160156.jpg
20200802_160138.jpg
20200802_160204.jpg
by stevemc32
Thu Jul 30, 2020 8:17 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Spent a couple of days working on the dovetail and got it somewhere close to where it should be. I've glued it up and I think that will be the last dovetail neck I do so it's time to get stuck into the bolt-on neck research. A heel cap of Tiger Myrtle is glued on and a tuner hole was plugged. I didn...
by stevemc32
Sun Jul 26, 2020 7:33 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

Got some adjustment done on the neck angle and it's now at a position that I reckon should work out. Didn't get a chance to work on the binding gaps yet.
20200726_170747.jpg
20200726_170913.jpg
by stevemc32
Sun Jul 26, 2020 2:18 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

That sounds like a pretty good idea, I'll give that a go.
by stevemc32
Sat Jul 25, 2020 11:56 pm
Forum: Instrument Builders Forum
Topic: Long time no build
Replies: 52
Views: 35129

Re: Long time no build

I was very lucky Mark in that I tooled up for guitar building when our dollar was worth more than the US dollar. I've been woodworking for a long time but the specific tools and jigs make it a much easier process. I just made my first Stewmac order since 2010 last night and paid almost double for th...